cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Former Member
Not applicable
Report Inappropriate Content
Message 1 of 7

Integrating external storage to the ESM device using CIFS method

Jump to solution

Hi All,

We are in the process of integrating an external storage device to the ESM combo device using CIFS method.

When we click on Storage Pools (Local Receiver-ELM >> Properties >> Storage Pools), I get the below mentioned warning;

"Your ELM management database is currently residing on the system drive along with the rest of the OS. If this drive runs out of free space, logging will stop and the existing log data will be lost. McAfee strongly recommends moving the database to a storage device with at least 500Gb free space. If your ELM is SAN capable, configuring the SAN volumes first and then migrate the DB using the option in the Receiver configuration tab."

Ignoring the above warning, we were successful in defining a storage device to be used with the storage pool for data retention. However we are unable to add a storage pool to hold the data.

While trying to configure a storage pool, we are getting the below error;

"The ELM management database is residing on the system drive. You must create an external storage device with at least 500Gb free and migrate the management database to it before you can configure the pools."

Can anyone suggest on how to resolve this issue.

Thanks in advance.

Regards,

Siddarth

1 Solution

Accepted Solutions
esher72
Level 9
Report Inappropriate Content
Message 3 of 7

Re: Integrating external storage to the ESM device using CIFS method

Jump to solution

You need to migrate your management database off of the ELM. Make sure that you do not migrate it to the same storage pool as your ELM logs. I am sorting out an ugly situation now because I made that mistake. Make sure that you have two separate storage pools: one for your management db and one for your ELM logs. Once you have the dedicated storage pool for the management db, you can migrate it from the ELM properties page. Go to "ELM Configuration" and click on the "Migrate DB" button. Then just pick the storage pool that you want.

View solution in original post

6 Replies
Former Member
Not applicable
Report Inappropriate Content
Message 2 of 7

Re: Integrating external storage to the ESM device using CIFS method

Jump to solution

Hi,

if you are running an All-In-One device you have to migrate the ELM Management DB before adding any storage pools.

esher72
Level 9
Report Inappropriate Content
Message 3 of 7

Re: Integrating external storage to the ESM device using CIFS method

Jump to solution

You need to migrate your management database off of the ELM. Make sure that you do not migrate it to the same storage pool as your ELM logs. I am sorting out an ugly situation now because I made that mistake. Make sure that you have two separate storage pools: one for your management db and one for your ELM logs. Once you have the dedicated storage pool for the management db, you can migrate it from the ELM properties page. Go to "ELM Configuration" and click on the "Migrate DB" button. Then just pick the storage pool that you want.

View solution in original post

Former Member
Not applicable
Report Inappropriate Content
Message 4 of 7

Re: Integrating external storage to the ESM device using CIFS method

Jump to solution

That's correct esher72.

But just to clarify your response - based on my testing, management database can only be migrated to "Storage device" not "storage pool".

So based on the recommendation, there needs to be at least two "storage devices" - one for management database (min size 500gb) and one or more for ELM log retention.

Once the storage device is set for mgmt db, you can migrate db from ELM properties.

Storage pools can be defined from the second storage device for log retention.

Former Member
Not applicable
Report Inappropriate Content
Message 5 of 7

Re: Integrating external storage to the ESM device using CIFS method

Jump to solution

Hi, Is it necessary to have atleast 500 GB free space for db migration, I've only 200 gb free space on test setup. Can I use it to migrate the data. As of now I am not able to see anything under devices. May not enough space could be the reason here.

Please suggest.

jon286
Level 9
Report Inappropriate Content
Message 6 of 7

Re: Integrating external storage to the ESM device using CIFS method

Jump to solution

I would imagine you do need it, seeing as in initial setup you must have 500gb free and allocated for the db, though I'm not sure of this.

I noticed this and that it's an older thread, so I was posting mainly to mention this;

The message from support for some time has been that CIFS is no longer supported (I may be behind the times with this in terms of this being published somewhere).

Former Member
Not applicable
Report Inappropriate Content
Message 7 of 7

Re: Integrating external storage to the ESM device using CIFS method

Jump to solution

Thanks Jon, at least I will not waste efforts on troubleshooting CIFS.

You Deserve an Award
Don't forget, when your helpful posts earn a kudos or get accepted as a solution you can unlock perks and badges. Those aren't the only badges, either. How many can you collect? Click here to learn more.

Community Help Hub

    New to the forums or need help finding your way around the forums? There's a whole hub of community resources to help you.

  • Find Forum FAQs
  • Learn How to Earn Badges
  • Ask for Help
Go to Community Help

Join the Community

    Thousands of customers use the McAfee Community for peer-to-peer and expert product support. Enjoy these benefits with a free membership:

  • Get helpful solutions from McAfee experts.
  • Stay connected to product conversations that matter to you.
  • Participate in product groups led by McAfee employees.
Join the Community
Join the Community